Ge-industrial-solutions Spectra Series Power Panelboards AMC6EBS, AMC4EBS, Bedienungsanleitung PDF herunterladen

Spectra Series™ Power Panelboards

Circuit Breakers and Modules

WARNING: Dan

er of electrical shock or in

Turn

OFF

ower ahead of the

anelboard or

switchboard before workin

inside the

ment or removin

com

onent. Do

not remove circuit

rotective devices or an

other com

onent until the

ower is turned

OFF.

General

These instructions apply to the following catalog numbers:

• Circuit breaker modules AMC6EB, AMC4EB,

AMC6EL, AMC6EBS, AMC4EBS, and AMC4SE

• Circuit breaker frames TEB, TED, THED, TEL,

SEDA, SEHA, SELA, and SEPA

Installation

1. Phase balancing for two-pole devices on three-phase

systems. To balance the panelboard load, remove the

screws on the appropriate bus clip, reposition the bus

clip as shown in Figure 1, then install and tighten the

screws to 27–32 in-lb.

Figure 1. Repositioning the bus clip to balance the load.

2. Prepare the module. Remove the protective caps or

insulating tape only from the tops of the stud posts to

which the circuit breaker is to be attached, as shown

in Figure 2. Fasten the filler supports, as shown in

Figure 3, with #10-32 x

/4" hex-head screws tightened

to 15–20 in-lb.

Figure 2. Removing the cap or tape from the stud posts of the

breaker module.

Figure 3. Attaching the filler breaker module.

3. Install the circuit breaker. Remove the lug cover, if

present. Place the

ON side of the breaker over the stud

posts, as shown in Figure 4. Secure the breaker to the

module with #10-32 screw and washer assemblies and

#8-32 x 2

/4" screws with cup washers. After all screws

are in place, tighten the #10-32 screws to 27–32 in-lb

and the #8-32 screws to 15–20 in-lb. Replace the lug

cover, if present.

GEH5625 Installation Instructions R04

A & C Phase

As Received

A & B Phase

B & C Phase

Protective Cap

or Insulating

Tape

Stud Post

Filler

Support

#10-32 x

/4"

Hex-Head

Screw

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Installation

gSpectra Series™ Power PanelboardsCircuit Breakers and ModulesWARNING: Danger of electrical shock or injury.Turn OFF power ahead of the panelboard

Seite 2 - Terminations

For double-branch devices, repeat this procedure forthe second breaker. Combinations of circuit breakertypes TEB, TED, THED, SEDA, SEHA, S

Seite 3

Seite 4 - GE Industrial Systems

gGE Industrial Systems General E

Weitere Dokumente für Ausrüstung Ge-industrial-solutions Spectra Series Power Panelboards AMC6EBS, AMC4EBS,

Um das Dokument anzuzeigen Ge-industrial-solutions Spectra Series Power Panelboards AMC6EBS, AMC4EBS, Bedienungsanleitung

Ge-industrial-solutions Spectra Series Power Panelboards AMC6EBS, AMC4EBS, Bedienungsanleitung (4 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Ge-industrial-solutions Spectra Series Power Panelboards AMC6EBS, AMC4EBS, Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Ge-industrial-solutions Spectra Series Power Panelboards AMC6EBS, AMC4EBS, herunter. GE Industrial Solutions Spectra Series Power Panelboards AMC6EBS, AMC4EBS, and AMC4SE User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Ausrüstung Ge-industrial-solutions Spectra Series Power Panelboards AMC6EBS, AMC4EBS,

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Ge-industrial-solutions Spectra Series Power Panelboards AMC6EBS, AMC4EBS,