Ge-industrial-solutions Spectra Series Power Panelboards 30–200 Ampere Fus Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Ge-industrial-solutions Spectra Series Power Panelboards 30–200 Ampere Fus herunter. GE Industrial Solutions Spectra Series Power Panelboards 30–200 Ampere Fusible Switch User Manual Benutzerhandbuch

Spectra Series™ Power Panelboards

30–200 Ampere Fusible Switch

WARNING: Dan

er of electrical shock or in

Turn

OFF

ower ahead of the

anelboard or

switchboard before workin

inside the

ment or removin

com

onent. Do

not remove circuit

rotective devices or an

other com

onent until the

ower is turned

OFF.

General

To comply with the National Electrical Code and

Underwriters Laboratories, the Canadian Electrical Code

and the Canadian Standards Association, the load center

must be installed in accordance with the information

included on the label on the inside of the equipment.

This must also be done in accordance with the applicable

local electrical codes and by a qualified electrical

contractor or licensed electrician.

WARNING: Hazard of electrical shock or burn.

Turn off

ower su

this e

ment

before working inside.

Installation

Use the following instructions to install a 30–200 ampere

fusible switch.

1. Remove the mounting bracket. Remove the two screws

shown in Figure 1 and remove the mounting bracket

from the switch.

Figure 1. Removing the mounting bracket from the switch.

2. Mount the removable mounting bracket. Install the

mounting bracket (removed from the switch in step 1)

on the power panelboard with the two self-tapping

screws provided, as shown in Figure 2. Tighten the

screws to 27–32 in-lb.

Figure 2. Installing the mounting bracket in the panelboard.

3. Install the switch. Align the locating hook tabs on the

bottom of the switch into the square holes in the

support rails on the panelboard interior, as shown in

Figure 3. Open the switch door and reattach the

screws removed in step 1 to the mounting bracket

installed on the panel in step 2. Tighten the screws to

27–32 in-lb.

Figure 3. Switch locating tabs aligned in the panelboard interior.

GEH5548 Installation Instructions R02

Mounting

Bracket

Screws

Mounting

Screws

Locating

Tabs

1 2

Installation 1
Systems Only 2

Inhaltsverzeichnis

Seite 1 - Installation

gSpectra Series™ Power Panelboards30–200 Ampere Fusible SwitchWARNING: Danger of electrical shock or injury.Turn OFF power ahead of the panelboard

Seite 2 - Systems Only

4. Wire the circuits. Refer to the label inside for theswitch cover for the proper tightening torques.5. Filler plates. Install filler plat

Weitere Dokumente für Ausrüstung Ge-industrial-solutions Spectra Series Power Panelboards 30–200 Ampere Fus

Um das Dokument anzuzeigen Ge-industrial-solutions Spectra Series Power Panelboards 30–200 Ampere Fus Bedienungsanleitung

Ge-industrial-solutions Spectra Series Power Panelboards 30–200 Ampere Fus Bedienungsanleitung (2 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Ge-industrial-solutions Spectra Series Power Panelboards 30–200 Ampere Fus Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Ge-industrial-solutions Spectra Series Power Panelboards 30–200 Ampere Fus herunter. GE Industrial Solutions Spectra Series Power Panelboards 30–200 Ampere Fusible Switch User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Ausrüstung Ge-industrial-solutions Spectra Series Power Panelboards 30–200 Ampere Fus

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Ge-industrial-solutions Spectra Series Power Panelboards 30–200 Ampere Fus